LST02 VER2, LCD Screen Tester
| MS492LEDD-KIT - New LED driver for testing from 18.5 to 24" LED screen
Please click here for more details
|
|
Need helps on setting up LST02 to test LCD Screen?
Please visit our reference table
|
LST02
LST02 has all LST01’s features,
plus a built–in LCD Controller that equips with our proprietary driver. By
setting a dip switch, panel supply voltage, and panel cable, it allows you to
apply any test pattern through
VGA input and test all types of specification on the LCD screen and LED Screen. In addition, a custom design Inverter
allows you to test any given number of CCFL back light lamp up to 4 at the time.
As of Jan 1st, 2012, 1366X768_HD_1_LVDS drive are installed in LST02.
To test LED screen, plese set all Dip switches Off. Disconnect 12V Jack and re-connect it back. Thtat's it!
Price: $229.99.
|
Quick Start Manual is also available in PDF format,
Download
|
|
Panel Wire Harness Connector:
This 30 pin connector has a polarity. Two white dots MUST face up when using our custom wire harness.
(Shown on next photo.)
Note: our panel wire harness can ONLY plug in one direction
Dip Switch
LST02 has Built-in Drives that supports all standard resolutions.
It is easy to change the resolution base on LCD panel specifications (or resolution chart).
To change Resolution:
Disconnect 12V DC Jack
Set dip switch based on resolution chart
Connect 12V DC Jack to LST02
Turn on LST02
Panel B+
Please refer to your LCD screen specification for the correct Panel voltage
supply. Most of Laptop screens are 3.3V
CCFL Back Light Lamp Connectors
LST02 has a custom built inverter, so you can connect any number of CCFL back light to it (Up to 4 CCFL Lamps).
Inverter Tester Connector
You can test any single lamp inverter. It is especially useful for Laptop screen repair.
6P for Inverter
This 6 pin connector is for testing an external inverter.
It is also a LED screen power supply.
Pin Assignments from left to right.
P1/P2=Power Ground
P3=Adj
P4=Enable
P5/P6=12V DC
LST02(V2) - How to use it
DB01 Driver Burner for LST02 |
$24.99 - shipping is $3 by USPS |
Our LCD Screen tester LST02 only comes with a standard resolution. So to test
the LCD screens that have non standard resolution, DB01 driver burner is needed.
DB01 allows you to load a non standard driver (resolution) into LST02. For
example: To test a 17.3?LED screen, you do need to set the resolution to
1600X900. But this resolution cannot accomplish by setting the dip switch. Then
DB01 is needed in order to load 1600X900_1LVDS driver into LST02. All drivers are
available at Cross Reference Table
|
|
DB_ Register is a program that you need to install in your computer,
so it could establish a connection between LST02 and DB1 throughout 9 pin serial cable.
DownLoad
DB01 comes with 9 pin serial data cable and 4 pin to 4 pin wire harness.
Click here for video instruction
PDF Manual - How to Use DB01
|
|
|
|
|
|
|
LST02 comes with the following items:
4-MS321EXT
1-DF14-20P-1LVDS
1-FIX-30S-1LVDS
1-FIX-30S-2LVDS
1-12V AC-DC Power Adapter(Not shwon on the picture)
1-15 Pin VGA Cable (Not shwon on the picture)
All new LST02 had loaded 1366X768_HD_1LVDS driver, so to test a LED screen. set all dip switch off, set B+ at 3.3V, Connect I-PEX-20455-040 to LST02 and LED screen. Apply signal to VGA and turn On LST02. That's it!
Note:These 3 Panel Cables are compatible with most of LCD screens. However, some LCD screens may require a special cable.
These Panel Cables can be purchased at $27.99 each with an additional $3 for ground shipping.
|
|
|
|
Resolution Chart
|
Resolution |
Size |
Panel Cable* |
1 |
2 |
3 |
B+ |
|
800X600 |
12" or smaller LCD Screen |
DF14-20P-1LVDS |
|
ON |
ON |
3.3V |
|
1024X768 |
14"-15" XGA Laptop Screen |
FIX-30S-1LVDS |
|
|
ON |
3.3V |
|
1024X768 |
15" XGA LCD Screen* |
DF14-20P-1LVDS |
|
ON |
|
3.3V |
|
1024X768 |
15" XGA LCD Screen* |
DF14-20P-1LVDS |
|
|
ON |
3.3V |
|
1280X800 |
12.1"-13.3" WXGA |
DF19-20P-1LVDS |
ON |
ON |
|
3.3V |
|
1280X800 |
14.0"-16.0" WXGA |
FIX-30S-1LVDS |
ON |
ON |
|
3.3V |
|
1280x1024 |
17"-19" SXGA LCD Screen |
FIX-30S-2LVDS |
ON |
|
|
5.0V |
|
1400X900 |
19" WXGA+ LCD Screen |
FIX-30S-2LVDS |
ON |
|
ON |
5.0V |
|
1600X1200 |
21" UXGA LCD Screen |
FIX-30S-2LVDS |
ON |
ON |
ON |
5.0V |
|
1366X768 |
15.6 & 16" LED Screen |
I-PEX-20455-040 |
|
|
|
3.3V |
|
|
|
* Do not know which wire harness do you need?
Please Click Here
|
Quick Start Manual is also available in PDF format,
Download
|
|
Sample Instructions - How to Use LST02
|
|
Need helps on setting up LST02 to test LCD Screen?
Please visit our reference table |
Replacement Parts for LST02
LCD Controller
Replacement LCD Controller for LST02
$69.99
|
|
4 CCFL Lamps Inverter
Custom Inverter for LST02
$69.99
|
|
Key PCB Assembly
6 Buttons Key PCB Assembly for LST02
$15.99
|
|
Front Assembly
Front Control Assembly for LST02
$59.99
|
|
|
New Arrival:
6.5" Open Frame Monitor
Sunlight Readable,
1000nits
$269.99
UB Series LED Backlight
UB series are the direct replacement for Industrial LCD screens that were originally equipped with 2, 4 and 6 CCFL
backlight lamps.
XB Sereis LED Backlight
XB Series is designed for smaller industrial LCD panels where space is limited by its original CCFL backlight assembly.
In other word, UB series LED strip cannot be mounting on these panels.
Touch Screen Inverter
These are brand new substitute backlight inverter module for Point-of-Sale screen,
ATM and other type of touch screen.
LCD Controller
These LCD Controller kits are designed to be easily integrated into the LCD screens that they are
commonly used in kiosks, POS, avionics, Vending machine, Digital Signage and all other applications.
LCD Screen
Looking for an industrial LCD screen?
Open Frame Display
Direct Drop in Replacement LCD display
Touch Screen
New Resistor and Surface Acustic touch screen
New Arrival:
10.4" Open Frame Monitor
Sunlight Readable, 1500nits
$269.99
LCD Controller
LCD Controller for
new 21.5" LED screen.
|